Open Access
Open access
,  том 2 ,  издание 5 ,  номер публикации 916

Chemical vapour treatment for enhancing the surface finish of PLA object produced by fused deposition method using the Taguchi optimization method

Тип публикации: Journal Article
Дата публикации: 2020-04-16
WOS Q2
SJR: 0.491
CiteScore: —
Impact factor: 3.2
ISSN: 25233963, 25233971
General Chemical Engineering
General Physics and Astronomy
General Materials Science
General Engineering
General Environmental Science
General Earth and Planetary Sciences
Краткое описание
In this study, the effect of process parameter and various post-processing techniques on surface roughness of PLA object produced by fused deposition method is investigated. The economical and versatile method with the proper design of the experiments to reduce the surface roughness is our objective. The PLA is selected as the workpiece material, a biodegradable material which is vastly used in medical implants, where surface roughness is a major issue. The various post-processing technique is analyzed, and the parameter optimization is taken into consideration. Post-processing technique like chemical treatment, vapour smoothing, sanding and polishing is carried out. Taguchi design of the experiment is also used to optimize the parameter that affects the targeted surface roughness. Taguchi L9 orthogonal array is used to organize the different parameters, and Minitab software is used to determine the optimum parameter setting. The dichloromethane chemical is found to be the best chemical for dissolving the PLA material and reducing the layer lines so that the surface roughness can be reduced. The final results confirmed that the chemical vapour treatment using dichloromethane and the Taguchi method sufficient to improve the surface roughness.
Для доступа к списку цитирований публикации необходимо авторизоваться.
Для доступа к списку профилей, цитирующих публикацию, необходимо авторизоваться.

Топ-30

Журналы

1
2
3
4
5
Progress in Additive Manufacturing
5 публикаций, 21.74%
International Journal of Advanced Manufacturing Technology
2 публикации, 8.7%
Rapid Prototyping Journal
1 публикация, 4.35%
Materials
1 публикация, 4.35%
Technologies
1 публикация, 4.35%
Journal of the Mechanical Behavior of Biomedical Materials
1 публикация, 4.35%
Polymer Bulletin
1 публикация, 4.35%
Izvestiya. Non-Ferrous Metallurgy
1 публикация, 4.35%
Russian Chemical Reviews
1 публикация, 4.35%
Solid State Phenomena
1 публикация, 4.35%
Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
1 публикация, 4.35%
International Journal of Fatigue
1 публикация, 4.35%
SpringerBriefs in Applied Sciences and Technology
1 публикация, 4.35%
Journal of Materials Engineering and Performance
1 публикация, 4.35%
Key Engineering Materials
1 публикация, 4.35%
AIP Conference Proceedings
1 публикация, 4.35%
International Journal of Metalcasting
1 публикация, 4.35%
Analytical Imaging Techniques for Soft Matter Characterization
1 публикация, 4.35%
1
2
3
4
5

Издатели

2
4
6
8
10
12
Springer Nature
12 публикаций, 52.17%
MDPI
2 публикации, 8.7%
Elsevier
2 публикации, 8.7%
Trans Tech Publications
2 публикации, 8.7%
Emerald
1 публикация, 4.35%
National University of Science & Technology (MISiS)
1 публикация, 4.35%
Autonomous Non-profit Organization Editorial Board of the journal Uspekhi Khimii
1 публикация, 4.35%
SAGE
1 публикация, 4.35%
AIP Publishing
1 публикация, 4.35%
2
4
6
8
10
12
  • Мы не учитываем публикации, у которых нет DOI.
  • Статистика публикаций обновляется еженедельно.

Вы ученый?

Создайте профиль, чтобы получать персональные рекомендации коллег, конференций и новых статей.
 Войти с ORCID
Метрики
23
Поделиться
Цитировать
ГОСТ |
Цитировать
Panda S. S. et al. Chemical vapour treatment for enhancing the surface finish of PLA object produced by fused deposition method using the Taguchi optimization method // SN Applied Sciences. 2020. Vol. 2. No. 5. 916
ГОСТ со всеми авторами (до 50) Скопировать
Panda S. S., Chabra R., Kapil S., Patel V. Chemical vapour treatment for enhancing the surface finish of PLA object produced by fused deposition method using the Taguchi optimization method // SN Applied Sciences. 2020. Vol. 2. No. 5. 916
RIS |
Цитировать
TY - JOUR
DO - 10.1007/s42452-020-2740-1
UR - https://doi.org/10.1007/s42452-020-2740-1
TI - Chemical vapour treatment for enhancing the surface finish of PLA object produced by fused deposition method using the Taguchi optimization method
T2 - SN Applied Sciences
AU - Panda, Subham Sekhar
AU - Chabra, Rimpy
AU - Kapil, Sajan
AU - Patel, Virendra
PY - 2020
DA - 2020/04/16
PB - Springer Nature
IS - 5
VL - 2
SN - 2523-3963
SN - 2523-3971
ER -
BibTex
Цитировать
BibTex (до 50 авторов) Скопировать
@article{2020_Panda,
author = {Subham Sekhar Panda and Rimpy Chabra and Sajan Kapil and Virendra Patel},
title = {Chemical vapour treatment for enhancing the surface finish of PLA object produced by fused deposition method using the Taguchi optimization method},
journal = {SN Applied Sciences},
year = {2020},
volume = {2},
publisher = {Springer Nature},
month = {apr},
url = {https://doi.org/10.1007/s42452-020-2740-1},
number = {5},
pages = {916},
doi = {10.1007/s42452-020-2740-1}
}
Ошибка в публикации?