Elsevier
Chinese Journal of Mechanical Engineering Additive Manufacturing Frontiers
,  том 2 ,  издание 2 ,  страницы 100076

Effects of Low-pressure Annealing on the Performance of 3D Printed CF/PEEK Composites

Тип публикации: Journal Article
Дата публикации: 2023-06-01
Elsevier
SJR: —
CiteScore: —
Impact factor: —
ISSN: 27726657
Краткое описание
The interlayer bonding properties are normally unsatisfying for 3D printed composites owing to the layer-by-layer formation process. In this study, low-pressure annealing was performed on 3D printed carbon fiber reinforced polyether ether ketone (CF/PEEK) to improve the interlayer bonding strength. The effects of annealing parameters on the mechanical properties and microstructure were studied. The results showed that the interlaminar shear strength (ILSS) of CF/PEEK improved by up to 55.4% after annealing. SEM and μ-CT were also applied to reveal the reinforcing mechanism. This improvement could mainly be attributed to the increased crystallinity of the CF/PEEK after annealing. Additionally, annealing reduced the porosity of the printed CF/PEEK and improved the fiber–resin interface. This resulted in a reduction in the stress concentration areas during loading, thereby enhancing the interlayer bonding strength of CF/PEEK.
Найдено 
Найдено 

Топ-30

Журналы

1
2
Virtual and Physical Prototyping
Virtual and Physical Prototyping, 2, 13.33%
Virtual and Physical Prototyping
2 публикации, 13.33%
Polymer Composites
Polymer Composites, 2, 13.33%
Polymer Composites
2 публикации, 13.33%
SAE Technical Papers
SAE Technical Papers, 1, 6.67%
SAE Technical Papers
1 публикация, 6.67%
Additive Manufacturing
Additive Manufacturing, 1, 6.67%
Additive Manufacturing
1 публикация, 6.67%
Journal of Adhesion Science and Technology
Journal of Adhesion Science and Technology, 1, 6.67%
Journal of Adhesion Science and Technology
1 публикация, 6.67%
Russian Chemical Reviews
Russian Chemical Reviews, 1, 6.67%
Russian Chemical Reviews
1 публикация, 6.67%
Composites Communications
Composites Communications, 1, 6.67%
Composites Communications
1 публикация, 6.67%
Additive Manufacturing Frontiers
Additive Manufacturing Frontiers, 1, 6.67%
Additive Manufacturing Frontiers
1 публикация, 6.67%
Results in Engineering
Results in Engineering, 1, 6.67%
Results in Engineering
1 публикация, 6.67%
Composites Part B: Engineering
Composites Part B: Engineering, 1, 6.67%
Composites Part B: Engineering
1 публикация, 6.67%
International Journal of Advanced Manufacturing Technology
International Journal of Advanced Manufacturing Technology, 1, 6.67%
International Journal of Advanced Manufacturing Technology
1 публикация, 6.67%
Journal of Materials Science
Journal of Materials Science, 1, 6.67%
Journal of Materials Science
1 публикация, 6.67%
1
2

Издатели

1
2
3
4
5
Elsevier
Elsevier, 5, 33.33%
Elsevier
5 публикаций, 33.33%
Taylor & Francis
Taylor & Francis, 3, 20%
Taylor & Francis
3 публикации, 20%
Springer Nature
Springer Nature, 2, 13.33%
Springer Nature
2 публикации, 13.33%
Wiley
Wiley, 2, 13.33%
Wiley
2 публикации, 13.33%
SAE International
SAE International, 1, 6.67%
SAE International
1 публикация, 6.67%
SPIE-Intl Soc Optical Eng
SPIE-Intl Soc Optical Eng, 1, 6.67%
SPIE-Intl Soc Optical Eng
1 публикация, 6.67%
Autonomous Non-profit Organization Editorial Board of the journal Uspekhi Khimii
Autonomous Non-profit Organization Editorial Board of the journal Uspekhi Khimii, 1, 6.67%
Autonomous Non-profit Organization Editorial Board of the journal Uspekhi Khimii
1 публикация, 6.67%
1
2
3
4
5
  • Мы не учитываем публикации, у которых нет DOI.
  • Статистика публикаций обновляется еженедельно.

Вы ученый?

Создайте профиль, чтобы получать персональные рекомендации коллег, конференций и новых статей.
Метрики
15
Поделиться
Цитировать
ГОСТ |
Цитировать
ГОСТ Скопировать
Yu X. et al. Effects of Low-pressure Annealing on the Performance of 3D Printed CF/PEEK Composites // Chinese Journal of Mechanical Engineering Additive Manufacturing Frontiers. 2023. Vol. 2. No. 2. p. 100076.
ГОСТ со всеми авторами (до 50) Скопировать
Yu X., Wu S., Zheng J., Chen Y., Luo L., Fan C., Shan Z. Effects of Low-pressure Annealing on the Performance of 3D Printed CF/PEEK Composites // Chinese Journal of Mechanical Engineering Additive Manufacturing Frontiers. 2023. Vol. 2. No. 2. p. 100076.
RIS |
Цитировать
RIS Скопировать
TY - JOUR
DO - 10.1016/j.cjmeam.2023.100076
UR - https://doi.org/10.1016/j.cjmeam.2023.100076
TI - Effects of Low-pressure Annealing on the Performance of 3D Printed CF/PEEK Composites
T2 - Chinese Journal of Mechanical Engineering Additive Manufacturing Frontiers
AU - Yu, Xiao
AU - Wu, Song
AU - Zheng, Jinghua
AU - Chen, Yiwei
AU - Luo, Li
AU - Fan, Congze
AU - Shan, Zhongde
PY - 2023
DA - 2023/06/01
PB - Elsevier
SP - 100076
IS - 2
VL - 2
SN - 2772-6657
ER -
BibTex |
Цитировать
BibTex (до 50 авторов) Скопировать
@article{2023_Yu,
author = {Xiao Yu and Song Wu and Jinghua Zheng and Yiwei Chen and Li Luo and Congze Fan and Zhongde Shan},
title = {Effects of Low-pressure Annealing on the Performance of 3D Printed CF/PEEK Composites},
journal = {Chinese Journal of Mechanical Engineering Additive Manufacturing Frontiers},
year = {2023},
volume = {2},
publisher = {Elsevier},
month = {jun},
url = {https://doi.org/10.1016/j.cjmeam.2023.100076},
number = {2},
pages = {100076},
doi = {10.1016/j.cjmeam.2023.100076}
}
MLA
Цитировать
MLA Скопировать
Yu., Xiao, et al. “Effects of Low-pressure Annealing on the Performance of 3D Printed CF/PEEK Composites.” Chinese Journal of Mechanical Engineering Additive Manufacturing Frontiers, vol. 2, no. 2, Jun. 2023, p. 100076. https://doi.org/10.1016/j.cjmeam.2023.100076.