Фаллахи Алиреза Арезодар

ALIREZA FALLAH AREZODAR

Professor, : afallahi@aut.ac.ir

Mech.Eng.Dep. Amirkabir Univ. of Tech

No 424, Hafez Ave, Tehran, IR,

Phone: (+98 21) 64543453,

Fax : (+98-21) 66419736

.

B.Sc.(Metallurgical. Eng.) Sharif University

of Tech. Tehran. Iran. 1976.

M. SC (Metalic and Ceramic Mat.)

UMIST. U.K. 1986.

Ph.D. (Metallurgy and Manufacturing

Process) Sheffield, U.K. 1990.

PROFESSIONAL EXPERIENCE

Sabbatical Leave at

MSU, Michigan State University, East

Lansing 2003 to 2004

Professor, Mechanics Department of

Amirkabir Univ. of Tech. Tehran, 1990 up to

date.

Managing Director of Post Graduate

Office, Amirkabir Univ. Tehran, Iran, 1996

to 2002.

Vice Chancellor in Research of Tarbit

Modares Univ. Tehran. Iran. 1991-1993.

Managing Director of Research

Office, Amirkabir Univ. of Tech. 1986-1987.

Board Member and Vice President of IDRO

Tehran, Iran, 1983-1985.

Board Member and chief in Metallurgy

Affair of Machine Tools Manufacturing Co.

Tabriz 1981-1983.

Metallurgist in Foundry shop

of Mech. Eng. Section in I.S.Co. 1976-1978.

of Tech. Tehran. Iran. 1976.

EDUCATION

B.Sc.(Metallurgical. Eng.) Sharif University of Tech. Tehran. Iran. 1976.

M. SC (Metalic and Ceramic Mat.) UMIST. U.K. 1986.

Ph.D. (Metallurgy and Manufacturing Process) Sheffield, U.K. 1990.

PROFESSIONAL EXPERIENCE

Sabbatical Leave at MSU, Michigan State University, East Lansing 2003 to 2004

Professor, Mechanics Department of Amirkabir Univ. of Tech. Tehran, 1990 up to date.

Managing Director of Post Graduate Office, Amirkabir Univ. Tehran, Iran, 1996 to 2002.

Vice Chancellor in Research of Tarbit Modares Univ. Tehran. Iran. 1991-1993.

Managing Director of Research Office, Amirkabir Univ. of Tech. 1986-1987.

Board Member and Vice President of IDRO Tehran, Iran, 1983-1985.

Board Member &Chief in Metallurgy Affair, MachineToolsManufac.Co.Tabriz1981-83

Metallurgist in Foundry shop of Mech. Eng. Section in I.S.Co. 1976-1978

MAJOR RESEARCH AREAS

Computational modeling and simulation with application to materials of Nano-and micro-scale

mechanical behavior of materials.

Fatigue and Tensile properties of Dual Phase Steel produced by controlled rolling process and

heat treatment.

Investigation on Microstructure - Processing - Mechanical Properties Relationship of Dual phase

steels by NDT.

Creep, Fatigue & Fracture of Materials; Fracture Initiation/Propagation Parameters fpr Duplex

TiAl Grain Boundaries Based on Twinning, Slip, Crystal Orientation and Boundary

Misorientation .

The Effects of Controlled Rolling on the Fatigue Behaviour of STE 500 steel.

Dental materials Creep and Fatigue Behavior.

Fatigue Properties of Soldered Minalux and Verabond II Ni Based Dental Alloys.

Formability and Metal forming Process;

Deep Draw-ability Behavior of Dual Phase Steel including forming limit Diagrams, R value as

the formability criteria relating to microstructure and processing parameters.

Investigation on Major Factors Affecting Forming Limit Diagrams of Automobile Sheets.

Some Investigations on the forming Behaviour of the St 14 sheets are used in the Automotive

Industries and Methods to Improve Indigenous sheets properties. Analytical and Experimental

Investigation on The plastic wrinkling during inward Tube Forming.

Analysis of Incremental Deformation of Deformable Projectile into Semi-infinite Target.

Penetration Analysis of Long Rod Projectiles into Semi – Infinite Targets and Extension to

Multi-Layer Targets.

Influence of Thermomechanical parameters on the Earing Behaviour of 1056 and 1100 Al alloys.

Effects of Metallurgy & Manufacturing Process Parameters on Microstructure and Properties of

Materials;

Research on Surface wear of the Auto-body Forming Die and Surface Hardness improvement by

Flame Hardening.

The Effect of Quenched - Tempered and Aus-tempering Heat Treatment on Fatigue Properties

of Coil Spring Steel.

A Study of Parameters Affect the Rehocasting processing to change Microstructure in the Al-

Cu alloys.

RECENT WORK IN PROGRESS:

1. Effect of layer lay-up on formability of Al–Cu two-layer sheet in electromagnetic

forming, Milad Shabanpour, Alireza Fallahi Arezoodar, INTERNATIONAL JOURNAL

OF ADVANCED MANUFACTURING TECHNOLOGY,

https://doi.org/10.1007/s00170-020-06319-1

2. Arshad Yazdanpanah , Farid Reza Biglari , Alireza Fallahi Arezoodar &Manuele Dabalà

2020, Role of grinding induced surface residual stress on probability of stress corrosion

cracks initiation in 316L austenitic stainless steel in 3.5% sodium chloride aqueous

solution, CORROSION ENGINEERING, SCIENCE &, TECHNOLOGY

https://doi.org/10.1080/1478422X.2020.1812818 , Taylor & Francis, published online

3. Milad Shabanpour, Alireza Fallahi Arezoodar, Effect of Strain Rate Investigation on

Forming Limit Diagram of Al-Cu Two-Layer Sheet, Modares Mechanical Engineering,

V. 20 , issue 8, PP 2159-2169, ISSN No 1027-5940, 2020; published online

http://mme.modares.ac.ir/article-15- 42028-fa.html

4. Asmani M. , Alireza Fallahi Arezoodar, The correlation between microstructure features

and tensile properties of