Surface Science Spectra

Abstract In this work we investigate the quartz etching process using hydrofluoric acid for trapped charge dating (TCD) applications. It is done using material collected from an active sand mine in Bełchatów Nowy Świat, central Poland. Approximately 20 kg of material was collected and prepared using routine procedures that are applied in TCD laboratories. The material was sieved using 180–200 μm meshes, and the selected fraction was etched for various time intervals. Sieved samples were etched for durations from 0 min up to 180 min and measured with microscope image analysis (IA), laser diffraction (LD), and mass loss which were used to estimate the depths of etching. Our results show statistical data on how non-uniform the etching process is. We estimate this as a function of etching time from IA, LD and mass loss. In our investigation, mass loss measurements with the assumption of spherical grains correspond to the decrease of radius of ca. 0.151 ± 0.003 μm · min−1. In case of LD, a rough etch depth estimation corresponds to a range 0.06–0.18 μm · min−1 with median at 0.13 μm · min−1. Microscope IA gives a 0.03–0.09 μm · min−1 with a median at 0.05 μm · min−1. Moreover, quartz grains are fractured into smaller pieces while etching. It means that assumptions that are used in etch depth estimation from mass loss are not correct. They incorrect not only because grains are not spheres but also because the number of grains is not constant. Therefore, the etch depth estimated from mass loss might be overestimated. Using microscope IA we report etch depth ranges that might be used to roughly estimate the etch depth uncertainty.

Abstract This work considers the impact of the internal alpha and beta dose rates in quartz grains obtained from sandy sediments on the results of luminescence dating. The internal dose rates reported here (ca. 0.01–0.21 Gy · ka−1) play a particularly important role, because of low (ca. 0.8–0.9 Gy · ka−1) or very low (ca. 0.4–0.6 Gy · ka−1) external dose rates. In these cases, the internal dose rates form a significant fraction of the total dose rates, often exceeding 10%. Ignoring this contribution would have made the considered luminescence ages artificially older. In our study, we measure both the internal alpha and beta contributions as the latter is usually neglected in the case of quartz. The dose rate measurements were performed using the innovative μDose system.

Abstract The E1’ centre is one of the most common paramagnetic defects observed by electron spin resonance (ESR) in natural quartz, the formation of which is, however, quite complicated. The dose response to gamma ray irradiation of the E1’ centre in natural quartz was systematically investigated in the present study to find that its dose response depends on the heating conditions of the sample before irradiation. The signal intensity decreases on irradiation when quartz has been heated up to 300°C, while it increases when heated above 400°C. The phenomena can be explained by the electronic processes that heating supplies electronic holes to the oxygen vacancies while gamma ray irradiation supplies electrons.

Abstract The precise chronology of the fluvial terraces of the Yellow River in China is essential to understand its geomorphological evolution history. More terrace ages are needed for the correlation of the terraces along the river and the construction of the longitudinal profile. In this study, seven terraces (T1–T7) in the Heiyukou area of the Jinshaan Canyon of the river were identified and were sampled for optical dating. The reliability of the ages was evaluated on the bases of bleachability, comparison of optical ages on fine and coarse grains, stratigraphic consistency of OSL ages, age distribution and geomorphological setting. The results show that the paired T2 terrace was formed at 72 ± 3 ka, and the T4, T5 strath terraces were dated to 108 ± 4 and >141 ± 4 ka, respectively. The ages for the samples from T6 and T7 were significantly underestimated, and the ‘infinitely old’ pre-Quaternary Red-Clay sample on the T7 terrace was dated to 134 ± 6 ka. The long-term river incision rates were calculated to be <0.36, 0.34 and 0.18 mm/a for at least the past 141, 108 and 72 ka, respectively, which also reflect the uplift rates of the Ordos plateau. The implication for dating terrace deposits is that terraces should be systemically sampled and dated using both fine and coarse grain fractions. The reliability of the ages obtained for high terraces should be evaluated using a relative chronology of dated samples on a case-by-case basis, if no independent numerical age controls are available.

Abstract Five dating protocols with post-infrared infrared (IR) stimulated luminescence signals (i.e. pIRIR) were performed on the K-feldspar of loess samples. Two of them were the single-aliquot regenerative-dose protocol (SAR) with two-step pIRIR stimulation, with the first IR stimulation at 50°C or 200°C and the second at 290°C (pIR50IR290, pIR200IR290). Two of them were the SAR protocols with five-step or six-step IR stimulation at multiple elevated temperatures to 250°C or 300°C (MET-pIRIR250, MET-pIRIR300). The final one was the multiple-aliquot regenerative-dose (MAR) protocol with the MET-pIRIR300 signal, together with a 500°C heat treatment administered before the test dose (‘MAR with heat’). The results show that when the equivalent dose (D e) of the sample was less than 500 Gy, all of the protocols gave consistent results; however, when D e exceeded 750 Gy, all of the SAR protocols underestimated De . The pIR50IR290 signal had the highest degree of underestimation, while the pIR200IR290, MET-pIRIR250 and MET-pIRIR300 signals had similar De values and similar degrees of underestimation. Possible reasons for the SAR D e underestimation are discussed. We suggest that only the ‘MAR with heat’ protocol is suitable for samples with D e exceeding 750 Gy.

Abstract The present study aimed at quantifying the relationship between TL and either CW-OSL or LM-OSL using commercially available magnesium oxide. The samples were bleached at two different temperatures, and a component-resolved analysis on the integrated signals was performed. According to the data of the present study, each one among the five observed LM-OSL component receives electrons from at least two different TL peaks. Two different fast OSL components were resolved in the LM-OSL curves, both accumulating electrons from all TL glow peaks with Tmax>150°C. Component C3 is very well correlated with the TL peaks at 102, 135 and 194°C, while components C4 and C5 are related to the TL glow peaks of 292°C, 353°C and 464°C. We note that for CW-OSL the resolution is good when two or more components differ in intensity by an order of magnitude. Blue stimulation depletes substantially the first two TL peaks but not the third peak. Substantial depletion of the high-temperature TL peaks is achieved only by using the LM-OSL configuration. The results of the present study suggest that the traps that contribute to TL and OSL are the same, despite using different recombination pathways.

Abstract Optically stimulated luminescence (OSL) dating of fine-grained (4–11 μm) fluvial sediments is rarely attempted but is crucial for constraining the evolution of mud-dominated floodplains. This study investigated the applicability of OSL dating to fine-grained deposits in the Mekong River, Cambodia based on a very young (<600 yr) point-bar to riverbank succession and modern flood deposits. In succession, fine-grained quartz OSL provided the youngest ages, whereas age estimates by multi-grain sand-sized quartz OSL, and feldspar and polymineral infrared-stimulated luminescence are >200 years older than the fine-grained quartz OSL age estimates. Ages of fine-grained quartz OSL are concordant with the minimum ages obtained from the single-grain quartz OSL. These results are supported by the generally small residual doses (<0.1 Gy) measured in modern fine-grained flood-plain deposits. This indicates that fine-grained sediments in the Mekong River (Cambodia) are sufficiently bleached at deposition and can yield reliable quartz OSL ages for establishing the chronology of the floodplain. The sufficient bleaching of fine-grained quartz partly results from the long transport distance and may also occur in other large river systems.

Abstract To assess if the heat-treated E 1′ centre in quartz is suitable for fluvial sediment provenance tracing, eight granitic samples from sediments and their source rocks with distinct geological ages and origins were collected for electron spin resonance (ESR) measurements. The results show that the maximum heat-treated E 1′ signal intensity of quartz in the fluvial sediments occurs upon heating at about 300°C, as previously observed in aeolian quartz. The heat-treated E 1′ signal intensity of quartz in sediment samples also shows significant correspondence to those of their source rocks as well as their formation age. We propose that the heat-treated E 1′ centre of sedimentary quartz, combined with other lithological discrimination parameters, could serve as an effective indicator for fluvial sediment provenance tracing.

Abstract The post-infrared (post-IR) pulsed blue light stimulated luminescence (PBLSL) signal has been employed to determine the equivalent dose (D e ) of feldspar contaminated quartz grains, but it sometimes suffers from the interference of feldspars. Since the green light stimulated luminescence (GLSL) signal of feldspars might be more reduced by a prior IR stimulation, we compared the characteristics of post-IR PBLSL and post-IR pulsed GLSL (post-IR PGLSL) signals of quartz and feldspars in this study to evaluate the feasibility of employing the green light for pulsed stimulation. We investigated the effect of the signal integration period, pulsed stimulation temperature, and prior IR stimulation temperature on the intensities of post-IR PBLSL and post-IR PGLSL of quartz and feldspars, and evaluated the potential feldspar interference on these two signals for the hypothetical and artificial quartz-feldspar mixture. The results demonstrate a lower feldspars contribution for the post-IR PGLSL signal. The feldspar interference only slightly increases with the increase of integration period for the post-IR PGLSL signal measured at low stimulation temperature, which permits a long integration period to be employed to enhance the signal to noise ratio. This study shows that the green light is a promising alternative for pulsed stimulation to suppress the feldspar contribution.

Abstract At the eastern tip of Anjihai anticline on the northern piedmont of Tian Shan (northwest China), deformed fluvial deposits have recorded active folding since the Pleistocene, but the absence of accurate ages makes it difficult to evaluate the anticline's shortening rate. Geological studies ascribed the fluvial strata to the early Pleistocene, which poses potential challenges for luminescence dating. In this study, multi-methods luminescence dating was applied to a fluvial sand sample taken from the sandy bed of the deformed basal strata. Single grain post-Infrared Infrared Stimulated Luminescence (pIRIR) and multiple-aliquot-regenerative (MAR) dose along with multiple-elevated-temperature pIRIR (MET-pIRIR) procedures were applied to determine the paleodose of the sample. The methodological uncertainties, such as thermal transfer and initial sensitivity change, were treated by increasing the test dose and performing dose recovery test. With consideration of the potential partial bleaching and anomalous fading, various statistical metrics were applied to the De values determined by using the single grain pIRIR225, single grain pIRIR290 and MAR-MET-pIRIR290 signals. The minimum age model (MAM) De values are 11% – 17% lower than the central age model (CAM) De values in general, and the MAM De values determined by the single grain pIRIR procedures are underestimated by more than 40% when compared with those determined by MAR-MET-pIRIR290 procedure. The MAM MAR-MET-pIRIR290 De of 811 ± 44 Gy results in a burial age of 284 ka for the basal deformed fluvial strata, which is much younger than the proposed early Pleistocene age.

Abstract In terms of fine-grain luminescence dating applications, the efficiency of α-radiation in producing luminescence is an important issue when determining environmental dose rates. Efficiency is usually assessed by measuring the ratio of luminescence intensities induced by known α and β laboratory doses. Consequently, most thermoluminescence (TL)/optically stimulated luminescence (OSL) readers besides the standard 90Sr/90Y β-source can also be equipped with a 241Am α-source. A crucial point is, however, the calibration of these sources. The calibration of β-sources is routinely performed using standard quartz samples previously irradiated by a known γ-dose, though, in the case of α-sources, the procedure is less standardised, partly because there are no calibration materials with a known α-efficiency value. In this study, we aimed to cross-calibrate the built-in α-source of a RISØ TL/OSL DA-20 luminescence reader by testing and comparing five procedures, applying different samples (quartz and polymineral), different protocols multiple aliquot regeneration (MAR) and single aliquot regeneration (SAR) and different calibration sources. Throughout the tests, the performance of the fine-grain RISØ calibration quartz was also assessed. Regardless of the applied procedure, the calculated α-dose rates with one exception gave similar results. On the one hand, the applied polymineral sample due to potential fading, fairly high residuals after bleaching and relatively low infrared stimulated luminescence (IRSL) sensitivity proved to be the least optimal choice for cross-calibration. On the other hand, the tested natural fine grain quartz gave almost identical results when using different types of bleaching and different calibration α-sources. The mean dose rate determined for the source was 0.080 ± 0.004 Gy/s. The cross-calibration by using the RISØ fine grain quartz yielded somewhat higher but at the apparent uncertainty of luminescence dating still not significantly different dose rate for the source under calibration. Tests showed that the calibration quartz saturates at a relatively low α-dose, and the shape of α- and β-dose-response curves also depart from each other quite early, suggesting that cross-calibration with this material seems to be reliable only at low doses. For the first time, the a-value of the fine-grain calibration quartz was also determined using the freshly calibrated α-source, and the measurement yielded a 0.054 ± 0.003 value. We propose that after further validation of this result, the RISØ calibration quartz can ease the dose rate assessment of uncalibrated α-sources in the future.

Abstract There are still controversies for the lakes evolution time during late Pleistocene in arid/semiarid north China. Badain Jaran Desert (BJD) features the coexisting of modern lakes in the lowland of megadunes. Also, lots of lacustrine relics could be found distributed widely in the desert, some of them just beside the modern lakes. These lacustrine relics indicated the paleo lakes evolution and the paleo environmental changes in the desert. In this study, one 3.9 m depth lacustrine deposits section was studied in the southeastern BJD which is close to a modern lake Zongzegedan (ZZGD). The deposit ages of the section were obtained by using optical dating with both of quartz and K-feldspar grains. Optically stimulated luminescence (OSL) dating of quartz grains shows that this paleolake was appeared during 65–34 ka, which is in the Marine Isotope Stage (MIS) 3 period, without the saturation of the OSL signals. On the other hand, the high temperature infrared stimulated luminescence (pIR IRSL) dating results from K-feldspar grains show that the paleolake was existed from late MIS 5 to late MIS 4 (86–60 ka) period with also good luminescence characteristics. The further study suggested that the OSL signals from quartz grains in this section show thermal instability, which may lead to the age underestimation. So the reliable age of the existed paleolake should be obtained by using pIRIR signals from K-feldspar, indicated that the relative humid environment in the desert happened at late MIS 5. The paleolake has same position with modern lake in the desert may contain geomorphological indications.

Abstract Establishing a chronology of events is a critical step in reconstructing the palaeoclimate and it is important for all types of environmental records, including speleothems. Here, we analysed a unique series of flowstones deposited between 3.2 Ma (marine isotope stage (MIS) Km3) and 0.08 Ma (MIS 5). The studied flowstones are located in a classic karstic environment, the Račiška Pečina Cave in south-western Slovenia. Further, a detailed chronology of events was constructed based on oxygen isotope stratigraphy (OIS), combined with magnetostratigraphy and U-series dating. Two curves were selected as reference records where the LR04 record was used as the global curve and a Mediterranean record was used as the regional curve. The Račiška Pečina profile was divided into two segments separated by a principal disconformity. The lower segment correlated better with the regional Mediterranean curve, while the upper segment was with the global LR04 curve. These findings suggest that the main factors controlling environmental conditions in the cave area changed between 3.2 and 0.8 million years ago.

Abstract We sheared simulated-quartz gouges using a low-velocity rotary shear apparatus and evaluated the relationship between electron spin resonance (ESR) intensity and displacement quantitatively considering problems of contaminants. ESR intensity of E1’ centre increased while OHC and peroxy centre kept constant with the increasing displacement up to 1.4 m. Microstructural analysis showed grain size reduction and fracture of starting gouges; hence, the fracture can affect the change in ESR intensity. ESR measurements were also conducted for starting gouges with variable amounts of contaminants, and it was confirmed that the effect of contaminants on the change in ESR intensity was negligible. Moreover, we estimated the temperature rise by the frictional heating on the surface and between particles, and it was shown that the effect of frictional heating on ESR intensity was also negligible in our experimental condition. Therefore, we could clarify the relationship between ESR intensity and fracturing with various displacements separately from contaminants and frictional heating. The results imply that the zero-setting of ESR signals cannot occur by the fracture with low frictional heating at the shallow depth.

Abstract We assessed the residual dose of K-feldspar grains from modern and Holocene beach–shoreface sands at Kujukuri, eastern Japan. Samples from the modern foreshore and shoreface (to 34 m depth) show residual doses <0.2 Gy for infrared-stimulated luminescence (IR)50 measured during post-IR infrared-stimulated luminescence (pIRIR)50/150, equivalent to potential burial age overestimation of only several decades for given dose rates. Residual doses of 1–3 Gy are retained by pIRIR50/150, equivalent to 400–1,300 years; pIRIR50/290 residual doses are up to 30 Gy, suggesting possible overestimation by >10,000 years. Residual doses of Holocene sands were also assessed by comparison with radiocarbon ages, revealing consistent results with modern sands. The pIRIR50/290 results show no pronounced correlation of residual dose with water depth, except for a few samples from <5 m depth with residual doses several tens of per cent lower than those of deeper sands, suggesting that most samples were not fully bleached and that sustained subaerial sunlight bleaching diminishes the difficult-to-bleach component. Compared to the uncertainties associated with other factors, such as the fading correction, the residual doses of IR50 and pIRIR50/150 are negligible for samples older than late and early Holocene, respectively. In contrast, the residual dose of pIRIR50/290 may lead to critical age overestimation of Late Pleistocene deposits if the residual dose is not properly corrected.